Mediterranean 41 mm cast iron racing cylinder with 55 cc for your Sachs moped / moped with 503 2AL, AAL, 2BL, ABL CH engine.
The GPO Pomodoro cylinder kit (Italian for tomato) is the sun-ripened, refreshing alternative to comparable greenhouse racing cylinders. It impresses with its freshness in the lower rev range, powerful acceleration and pulling power, as well as a fruity finish in the upper rev range. The cylinder absorbs more nutrients than original ones, transforming them into juicy, powerful pulp and exuding a tantalizing aroma of oil. A real treat for your engine that fills the streets with passionate flavors.
Details:
- Grey cast iron reproduction cylinder with Ø 41.0 mm bore
- slot-controlled
- Ø 19 mm intake
- optimized Öoverflow channels
- improved timing
- no spindling of the engine housing necessary (Ø cylinder neck 45.0 mm)
- Ø external connection exhaust manifold: 26 mm
- incl. Ø 41 mm GPO piston
Differences to the original BADASS cylinder:
- Original or swiing® intake manifolds can be fitted
- The BADASS 15 mm & 17 mm intake manifolds cannot be fitted
- The cylinder cannot be adapted to a 502 or 50/2 engine
- Higher intake timing vs;higher intake timing compared to the BADASS
Due to the correct angle of the intake surface, both original and swiing® brand intake manifolds and carburettors fit under the side valving without the need for adjustments.
The GPO piston improves intake timing, resulting in higher engine speeds. The edges of all ports are smoothed, which enables optimum mixture flow.
Note: Replace the rubber silentblocs on 503 BL engines with aluminum bladders to avoid exhaust flange fatigue fractures at increased power. Ideally, you should use reinforced clutch springs to ensure that all the vitamins and minerals end up on the plate. For an additional flavor note, you can install a 32 mm resonance pot.
Protect the Pomodoro cylinder from heat with the original Sachs cylinder shield or the Pergola cylinder head in the optionally available accessories. You will also find a suitable swiing® irrigation system and piping there.
Good, inexpensive standard spare part. GPO – GOOD PARTS ONLY, in cooperation with GFO – GOOD FOOD ONLY.
The set includes the following fixed parts:
Hole pattern [mm]: 40 x 60 / 37 x 37 · Manufacturer: GPO · Material: Gray cast iron · Displacement: 57 ccm · Nominal diameter: 41 mm · Ø cylinder neck: 45 mm · Ø Outlet outside: 26 mm · Ø outlet inside: 22 mm · Ø Inlet inside: 19 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 32 mm · Outlet type: clamped
Manufacturer: GPO · Nominal diameter: 41 mm · Ø outside piston (A): 40.94 mm · Ø piston pin (B): 12 mm · Compression height (C): 28 mm · Curvature (D): 3.2 mm · Total piston height (E): 49.4 mm · Number of piston rings (F): 2 pcs · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Piston ring height: 1.5 mm · Thick piston ring: 1.8 mm · Piston weight: 86 g
Manufacturer: GPO · Material: Sealing paper, Sealing carton, Aluminum · Number of components: 3 pcs · Thickness: 0.3 mm, 1 mm · Ø cylinder: 41 mm · Hole spacing inlet: 0 - 32 mm
Details
| Manufacturer | GPO |
| Material | Gray cast iron |
| Area of application | Tuning |
| Displacement | 55 ccm |
| Nominal diameter | 41 mm |
| Crankshaft stroke | 43 mm |
| Ø piston pin (B) | 12 mm |
| Ø cylinder neck | 45 mm |
| Ø Outlet outside | 26 mm |
| Ø outlet inside | 22 mm |
| Ø Inlet inside | 19 mm |
| Thread inlet | M6x1 (standard thread) |
| Hole spacing inlet | 32 mm |
| Outlet type | clamped |
| Hole pattern [mm] | 40 x 60 / 37 x 37 |
Suitable for the following models
| Sachs | 503 - AAL, ABL, 2AL / 2BL |
Accessories & related products
Exhaust set "Tuning" chrome | Sachs 503 2AL/2BL
Manufacturer: Made in Portugal · Material: Steel · Surface: chrome-plated · Ø outside: 70 mm · Total length: 700 mm · Color: Chrome · Ø Flame tube outside: 28 mm · Exhaust type: Cigar · Mounting type: Screwed clamp · Flame tube attachment: Plug connection clamped
EUR 119.20
swiing resonance exhaust set Ø 28 / 70 mm | Sachs 503
Manufacturer: swiing · Material: Steel · Surface: chrome-plated · Ø outside: 70 mm · Total length: 730 mm · Color: Chrome · Ø Internal connection: 28 mm · Exhaust type: Cigar · Mounting type: Screwed clamp · Flame tube attachment: Plug connection clamped
EUR 167.00
swiing® revival silent blocks Alu Racing | Sachs 503 / 504 / 505 / 535
Material: Aluminum · Surface: anodized · Manufacturer: swiing® revival parts · Total length: 13 mm · Nominal diameter inside: 8.5 mm · Ø inside: 8.3 mm · Ø Bundle: 26 mm · Ø outside: 21.95 mm · Alternative version of the Pony OEM number: A4286 · Alternative version of the Sachs OEM number: 0251 121 000
EUR 28.50
GPO 43 mm "Pomodoro" cylinder kit | Sachs 503
Nominal diameter: 43 mm · Manufacturer: GPO · Material: Gray cast iron · Displacement: 63 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 45 mm · Ø Outlet outside: 26 mm · Ø outlet inside: 22 mm · Ø Inlet inside: 19 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 32 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Hole pattern [mm]: 40 x 60 / 37 x 37 · Area of application: Tuning
EUR 298.30
Moped fans like you also bought:
NSK BO15 shoulder ball bearing 15/40/10 (A4502)
Bearing type: Shoulder bearing · Bearing cage: Brass cage ball-guided · Inner ring width: 10 mm · Manufacturer: NSK · Area of application: Standard · Material: Brass · Material: Steel · Surface: blank · Stock number: BO15 · Ø outside: 40 mm · Ø inside: 15 mm · Width: 10 mm · Ball bearing closed: No · Pony OEM number: A4502 · Sachs OEM no.: 0932 007 001
EUR 29.70
swiing® ingenious 15 mm carburetor tuning camouflaged | Sachs 503
Nominal diameter: 15 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Aluminum · Component group Carburetor: Carburetor complete · Carburetor type: SRE · Choke control: Hand choke · Width: 50 mm · Nozzle thread: M3.5x0.6 (standard thread) · Ø fuel hose connection: 6 mm · Total length: 66 mm · Height: 95 mm · Nozzle size: 62 · Mounting type: Plug connection clamped · Ø Inside entrance: 15 mm · Ø Internal connection: 20 mm · Ø Output inside: 15 mm · Ø Air filter connection: 20 mm · Mixed oil connection: No · Vacuum connection: No · Nozzle block: 2.17 · Camouflaged: Yes · Clamping screw torque (max.): 4 N/m
EUR 95.40
swiing® revival air filter Racing | Sachs 503
Height: 52 mm · Width: 68 mm · Total length: 165 mm · Manufacturer: swiing® revival parts · Material: Plastic · Area of application: Tuning · Color: black · Filter type: Racing screen · Ø Internal connection: 20 mm · Mounting type: Plug connection clamped · Camouflaged: No
EUR 71.50
swiing® ingenious 15 mm intake manifold long version | Sachs 503 2AL, 2BL
Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Aluminum · Ø inside: 15 mm · Thread type: M6x1 (standard thread) · Mounting type: Screws · Number of fixing points: 2 pcs · Hole spacing inlet: 32 mm · Total length: 70 mm · Height flange center hole: 70 mm · Total height: 80 mm · Ø External connection: 20 mm · Camouflaged: No · Pony OEM number: A2176
EUR 71.50
GPO piston 40.94 mm | Sachs 502, 50/2, 50/3, 50/4
Nominal diameter: 41 mm · Manufacturer: GPO · Thick piston ring: 1.8 mm · Ø outside piston (A): 40.94 mm · Compression height (C): 28 mm · Curvature (D): 3.2 mm · Total piston height (E): 49.4 mm · Number of piston rings (F): 2 pcs · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Piston ring height: 1.5 mm · Ø piston pin (B): 12 mm · Piston weight: 86 g
EUR 47.60
Collection only possible with online purchase and appointment.
