Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Sachs moped / moped with 502, 50/2, 50/3, 50/4 engine and fan cooling.
The racing ignition comes complete with CNC-milled fan wheel and constantly supplies your cylinder with the optimum cooling.
The small rotor results in better acceleration and throttle response. If you want an even smoother idle, you can order the additional weight (optional) at the same time.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- Optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set the piston to TDC, the marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing point of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel; this achieves a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good ground (earthing), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal plug:
- 1 = black
- 2 = blue
- 3 = white
Attention: Under no circumstances should excessively long screws be used to mount the fan wheel, as otherwise the stator winding may be damaged. A suitable screw set is included in the scope of delivery.
When you purchase this complete set, you will receive a substantial percentage off the retail price of the individual parts.
The ignition is compatible with cable starters, which also fit the HPI, you can find these in the accessories section.
Exclusive product for the highest demands of the quality brand swiing®.
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: black · Ø outside: 110 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Number of fixing points: 6 pcs · Height: 25 mm · Weight: 116 g · Alternative version of the Pony OEM number: A1026 · Alternative version of the Sachs OEM number: 0211 070 105
Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Thread type: M6x1 (standard thread) · Drive: Slot · Number of components: 6 pcs
Manufacturer: swiing® ingenious parts
| Manufacturer | swiing® ingenious parts |
| Tension | 12 V |
| Light coil voltage | 12 V |
| Area of application | Tuning, High End, Racing |
| Performance | 60 W |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Mounting type | Screws |
| Ø Internal flywheel | 63.5 mm |
| Number of fixing points | 3 pcs |
| Ø Flywheel outside | 75 mm |
| Sachs | 502 (Saxonette) - AL, AML 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 50/4 - MLFB (2.6 PS), LKH (4.5 PS) |
Accessories & related products
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Ø cable: 5 mm · Ø cable: 7 mm · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Component group Carburetor: Spark plug connector · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
EUR 10.50
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Beta 521
Width across flats (trigger): 27 mm · Manufacturer: GPO · Clamping depth: 10 mm · Material: Steel · Surface: blackened · Number of components: 1 pcs · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Total length: 55 mm · Total length: 75 mm · Width across flats Screw: 19 mm · Strength class: 8.8 · Area of application: (Dis)assembly tool
EUR 11.80
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents [ml]: 10 ml · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m · Area of application: Chemistry
EUR 26.10
EUR 2’610.00/l
swiing® ingenious fan wheel red (EVO, HPI, Bosch, Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: red · Ø outside: 120 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Height: 13.5 mm · Weight: 87 g · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Number of fixing points: 10 pcs
EUR 74.50
swiing® ingenious fan wheel chrome (EVO, HPI, Bosch, Ducati) | Puch X30 Velux, Sachs 503, Belmondo
Manufacturer: swiing® ingenious parts · Ø mounting hole: 6 mm · Material: Aluminum · Color: Chrome · Ø inside: 39 mm · Surface: chrome-plated · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Height: 13.5 mm · Weight: 87 g · Number of fixing points: 10 pcs · Ø outside: 120 mm
EUR 82.10
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Candle thread type: short · Thread type: MF14x1.25 (fine pitch thread) · Spark plug socket: M4 · Electrode material: Iridium · Suppressed: No · Width across flats SW: 21 mm · Area of application: Cross · Area of application: High End · Area of application: Tuning
EUR 30.90
swiing® ingenious 280 g additional weight EVO Inox
Manufacturer: swiing® ingenious parts · Material: Chrome steel (known as Nirosta®) · Surface: electropolished · Ø bolt circle: 48 mm · Ø bolt circle: 54 mm · Thickness: 12 mm · Ø inside: 39 mm · Weight: 280 g · Ø outside: 95 mm · Ø mounting hole: 6.2 mm · Number of fixing points: 3 pcs · Area of application: Tuning
EUR 59.50
Moped fans also bought
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Oil type: GL4 · Viscosity (SAE): 80W · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Temperature resistance (min.): -30 - 220 °C · Area of application: Gearbox lubrication with clutch
EUR 11.80
EUR 26.22/l
swiing® revival shim set | Sachs 503, 502, 50/2, 50/3
Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Ø outside: 18 mm · Ø outside: 21 mm · Nominal diameter inside: 13 mm · Ø inside: 12.5 mm · Ø inside: 15.2 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Thickness: 0.5 mm · Thickness: 1 mm
EUR 20.10
swiing® ingenious fan wheel black (EVO, HPI, Bosch, Ducati) | Sachs 50/2, 50/3
Manufacturer: swiing® ingenious parts · Material: Aluminum · Color: black · Height: 25 mm · Ø bolt circle: 48 mm · Surface: anodized · Ø mounting hole: 6 mm · Ø inside: 39 mm · Ø outside: 110 mm · Weight: 116 g · Number of fixing points: 6 pcs · Alternative version of the Pony OEM number: A1026 · Alternative version of the Sachs OEM number: 0211 070 105
EUR 71.40
swiing® ingenious gasket cylinder head 41 mm | Sachs 503, 502, 50/2, 50/3, 50/4
Place of use: Cylinder head · Nominal diameter: 41 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Area of application: Standard · Ø cylinder: 41 mm · Ø inside: 41.7 mm · Thickness: 0.3 mm · Hole pattern [mm]: 37 x 37
EUR 5.85
Collection only possible with online purchase and appointment.
