High-quality three-jaw special clutch with woven aramid linings (commonly known as Kevlar) for your Puch moped with an E50 engine.
The plates of the centrifugal clutch feature larger lubrication holes, which minimize wear and reduce the weight to just 265 g. All metal parts are made of tough, high-quality S355 steel, which guarantees exceptional durability even under high loads.
We deliberately omitted retaining rings from the clutch plates and replaced them with 1.5 mm-thick washers. The entire E50 clutch is secured with a reinforcement plate and Torx countersunk screws, making the engine-clutch assembly 1 mm thinner overall. This also prevents the reinforcement plate from rubbing against the clutch bells.
Note: This clutch is not suitable for kick-start engines.
You can find individual clutch plates as well as alternative tuning or racing clutches in the accessories section.
A quality product from the Austrian manufacturer A.S.P. – Puch Parts.
| Ø outside | 91.5 mm |
| Thickness | 21.5 mm |
| Manufacturer | ASP |
| Material | Steel |
| Area of application | Tuning, Racing |
| Material addition | Aramid (colloquially known as Kevlar) |
| Number of jaws | 3 pcs |
| Recording type | Cone mounting |
| Number of springs | 6 pcs |
| Puch | E50 |
Accessories & related products
HK clutch "supersport" | Puch Maxi S / N (E50)
Ø outside: 93.3 mm · Manufacturer: HK Clutches · Material addition: Aramid (colloquially known as Kevlar) · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Area of application: Cross · Area of application: High End · Area of application: Racing
EUR 406.60
ASP clutch 2-jaw "woven" Aramid | Puch E50
Ø outside: 91.5 mm · Thickness: 21.5 mm · Manufacturer: ASP · Material: Steel · Material addition: Aramid (colloquially known as Kevlar) · Number of jaws: 2 pcs · Number of springs: 4 pcs · Area of application: Racing · Area of application: Tuning · Alternative version of the Puch OEM number: VM 477.0 · Alternative version of the Puch OEM number: 349.1.12.004.0
EUR 203.30
Not in stock
ASP clutch springs reinforced 50 N/mm | Puch E50
Spring design: Pressure spring · Spring rate: 50 N/mm · Ø wire: 1.8 mm · Manufacturer: ASP · Number of components: 3 pcs · Material: Spring steel · Area of application: Racing · Area of application: Tuning · Ø inside: 4.6 mm · Ø outside: 8.2 mm · Total length: 27 mm
EUR 21.40
Explore categories from Clutch
Moped fans also bought
swiing® revival nut / spring washer clutch E50 | Puch Maxi
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut 0.8D · Height: 8 mm · Drive: External hexagon · Nominal diameter (thread): 10 mm · Thread type: MF10x1 (fine pitch thread) · Width across flats: 17 mm
EUR 4.65
swiing® revival gasket gearbox cover engine 0.5 mm | Puch E50
Ø inside: 106 mm · Manufacturer: swiing® revival parts · Ø outside: 116 mm · Thickness: 0.5 mm · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Number of fixing points: 4 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
EUR 3.45
swiing® revival gasket gearbox cover engine 1 mm | Puch E50
Ø inside: 106 mm · Ø outside: 116 mm · Thickness: 1 mm · Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Number of fixing points: 4 pcs · Number of components: 1 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
EUR 4.65
Hot 
swiing® ingenious crankshaft "High End" with mounted bearings | Puch E50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 43 mm · Weight: 968 g · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø piston pin (B): 12 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 221.20
Not in stock
Hot
swiing® ingenious 17 mm SRF carburetor camouflaged | Puch Maxi, Supermaxi, X30 NS / NL
Carburetor type: SRE · Material: Aluminum · Total length: 65 mm · Width: 47 mm · Height: 89 mm · Height: 109 mm · Manufacturer: swiing® ingenious parts · Mounting type: Plug connection clamped · Component group Carburetor: Carburetor complete · Nominal diameter: 17 mm · Nozzle thread: M3.5x0.6 (standard thread) · Ø fuel hose connection: 5 mm · Nozzle size: 74 · Ø Inside entrance: 17 mm · Ø Internal connection: 23 mm · Ø Output inside: 17.1 mm · Ø Air filter connection: 27.5 mm · Area of application: Tuning · Camouflaged: Yes · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.2 · Clamping screw torque (max.): 3 N/m · Clamping screw torque (max.): 4 N/m
EUR 143.50
Working late? Evening hours on Thursday until 20:00
