Hot 
High-quality ADDY 4-bearing engine housing, which forms the engine block for a Puch moped with an E50 engine.
New features include a kickstand mount, milled (rather than cast) overflow channels, and a shallower cast recess for GME systems, allowing the housing to be bored out to accommodate large cylinders with a bore diameter of up to 58 mm. Furthermore, the serial number has been repositioned so that it is now located on the right side. This allows you to stamp the frame number into the top surface as needed.
The housing was specifically designed and manufactured for the tuning sector; therefore, some components—such as the mounting surface for a kickstarter—have been omitted.
The housing features the following special characteristics:
- Enlarged sealing surface in the area of the cylinder base
- Casing screws slightly offset outward, leaving more space for larger overflow channels
- Pre-milled surface for GME intake systems
- Locating pins for secure positioning when assembling the housing halves
- Additional threads for more flexible ignition installation
- Extra-large cooling fins in the lower section for better heat dissipation and thus reduced wear on the crankshaft bearings
- Stand mount, 3 M6 threads at the original spacing
- Approved for all SAM moped racing and moped cross categories
- Cylinder stud hole pattern: 44 x 44 mm
- Cylinder neck diameter: 48.4 mm (can be reamed up to 58.0 mm if no GME is installed)
Installation tips:
- When installing original intake components and an SRE carburetor, a 2 mm-thick intake gasket must be used to ensure the float chamber does not rest on the GME block.
- Using the included washers, various gear wheels with different positions—such as those found in 3-bearing or MBR transmissions—can be properly spaced. Be sure to check that the gear wheel is properly centered before reassembly!
- Use the following screw lengths: 7 pcs. M6 x 35 mm / 6 pcs. M6 x 50 mm
Note: If you plan to use a center stand, we recommend using a sturdy center stand, as there is a stand stop only on the left side.
A quality product from the ADDY by Schöb Engineering brand.
Alternative to the original Puch part number: 349.3.10.332.0
| Manufacturer | ADDY |
| Material | Aluminum |
| Alternative version of the Puch OEM number | 349.3.10.332.0 |
| Puch | E50 |
Accessories & related products
GPO Gasket Set for E50 Engine | Puch Maxi S, N
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Area of application: Standard · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Decompressor: Yes · Hole spacing outlet: 42 mm · Hole spacing inlet: 32 - 38 mm · Hole pattern [mm]: 44 x 44
EUR 11.90
swiing® revival crankshaft "original" | Puch E50
Manufacturer: swiing® revival parts · Material: Steel · Cheek type: standard · Crankshaft stroke: 43 mm · Thread type: MF10x1 (fine pitch thread) · Thread type: MF8x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Weight: 873 g · Area of application: Standard · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Thread length: 15 mm · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 107.50
Hot
swiing® ingenious crankshaft "High End" with mounted bearings | Puch E50
Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Weight: 968 g · Crankshaft stroke: 43 mm · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Thread length: 11 mm · Thread length: 15 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø piston pin (B): 12 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 221.20
Not in stock
Explore categories from Gearbox & housing (motor)
Moped fans also bought
swiing® revival oil filler plug with sealing ring | Puch E50
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Number of components: 2 pcs · Drive: Slot · Nominal diameter (thread): 10 mm · Screw head: Lens head · Total length: 14.6 mm · Thread length: 6 mm · Ø External head: 14 mm · Thread type: M10x1.5 (standard thread) · Puch OEM number: 364.1.10.660.1
EUR 4.65
swiing® revival Stud Bolt Set M6x106 | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.9 mm · Drive: External hexagon · Nominal diameter (thread): 6 mm · Total length: 106 mm · Thread length: 13 mm · Thread length: 18.5 mm · Thread type: M6x1 (standard thread) · Width across flats: 10 mm · Alternative version of the Puch OEM number: 360.1.10.034.1
EUR 8.85
MBR clutch basket 18 teeth Racing straight | Puch E50
Manufacturer: MBR · Material: Steel · Area of application: Tuning · Toothing type: straight toothed · Number of teeth: 18 pcs · Ø inside: 15 mm · Ø inside: 17 mm · Ø outside: 99.5 mm · Recording type: Interlocking · Ø Receptacle: 31 mm · Height: 49 mm
EUR 221.20
Working late? Evening hours on Thursday until 20:00
